P0064 Code - HO2S Heater Control Circuit High Bank 2 Sensor 3

What Does Code p0064 Mean?

It will usually mean that a rich air-fuel ratio is being detected. The computer of the vehicle (PCM) will then attempt to correct the air-fuel ratio by decreasing the amount of fuel the engine receives.

The PCM will regulate the air-fuel ratio and attempt to keep it at or near the stoichiometric range of 14.7:1. The stoichiometric range is ideal because it regulates the consumption of fuel, and limits the amount of harmful pollutants that an engine will produce.

engine code P0064	P0064 fix	obd P0064	dtc P0064
obd code P0064	obd2 P0064	P0064 car code	diagnostic code P0064
car code P0064	check engine code P0064	fehlercode P0064	P0064 fiat
codigo P0064	codigo falla P0064	P0064 kody błędów	codigo de falla P0064

What are the common causes of P0064 ?

Potential causes of a P0064 code include:

• Faulty Bank 2, 3 HO2S (Heated Oxygen sensor)
• Open in the heater control circuit (12 volt PCM controlled systems)
• Short to B+ (battery voltage) in the heater control circuit (12 volt PCM controlled systems)
• Open ground circuit (12 volt PCM controlled systems)
• Short to ground on heater control circuit (On PCM ground controlled systems)

How do you troubleshoot P0064 ?

NOTE #1: It should be noted that code P0064 indicates a fault in the oxygen sensors’ heating control circuits, rather than issues with fuel/air metering. In cases where codes relating to fuel/air metering are present along with P0064, these codes must be resolved before starting an electrical diagnosis of code P0064.

NOTE #2: At the risk of overstating the case, code P0064 relates to oxygen sensors that are located after the catalytic converter. To avoid confusion, and prevent testing/replacement of the wrong oxygen sensors, always consult the repair manual to determine the location, color-coding, and routing of the wiring associated with #3 oxygen sensors.

NOTE #3: Check for, and repair all exhaust leaks before starting an electrical diagnosis of code P0064. Exhaust leaks can contaminate the atmospheric air used by oxygen sensors, which contamination can result in inaccurate readings.

Step 1

Record all fault codes and available freeze frame data. This data can be useful in cases where an intermittent fault is diagnosed later on.

Step 2

Perform a thorough visual inspection of all associated wiring and connectors. Look for damaged, shorted, burnt, or broken wiring and connectors. Replace wiring and/or connectors as required, and rescan the system to see if the code returns.

NOTE: On some applications, the input voltage is supplied through a fused circuit. Be sure to check associated fuses during the initial inspection of the wiring.

Step 3

If the code persists, perform reference, continuity, and resistance tests on all associated wiring. Input voltage must be equal to battery voltage (12.6 to 13.8-volts), so be sure to check that the battery is fully charged. Be sure to disconnect the sensor from the
PCM before starting continuity checks to prevent damage to the controller.

Pay particular attention to the resistance of the sensor, which should be 8 Ohms, or very close to it. Compare the obtained resistance reading to the value stated in the manual, and replace the sensor if it deviates from the stated value. Remove the sensor from the exhaust system, and be sure to unplug the connector to get the most accurate resistance reading.

NOTE: Be aware that on some applications, the input voltage is supplied by the PCM, and in these cases the input voltage will not be routed through a fuse. On some applications the ground is also supplied by the PCM in Key-On-Engine-Off mode, while on other applications the engine needs to run for a ground to be present. Consult the manual on this point.

Step 4

While the oxygen sensor is removed from the system, inspect the element for signs of discoloration, or the presence of deposits. Some aftermarket fuel and oil additives contain silicone-based compounds that can cause deposits to form on spark plugs and oxygen sensors. Note that oxygen sensors cannot be cleaned to remove deposits; the only reliable remedy is to replace the sensor, and not to use any sort of oil/fuel additives

Step 5

It deposits and discoloration is found, replace the sensor, and retest the system to verify that all voltages/resistances fall within the manufacturers specifications. If all readings check out OK, start the engine and allow the PCM to enter closed loop operation.

If the sensor was replaced and the wiring is in good shape, the code scanner should indicate a reading that falls close to the mid-point between a rich-, and lean running condition. A variation of around 100-, to 200 millivolts to either side of the mid-point is acceptable, but the reading should remain constant if the engine speed does not change.

Changing the engine speed should produce an almost immediate change in the displayed reading; if no change is observed, or there is a significant time lag (more than 5 to 8 seconds or so) before the reading changes, the sensor is defective- assuming of course that there is no damage or corrosion present on the connector.

Check the connector again; if it is in a less-than-perfect condition, repair/replace it, and check the sensors’ operation again. If the fault persists after repairing the connector, replace the sensor if it was not replaced previously after the inspection for discoloration or the presence of deposits.

NOTE: Bear in mind that the overall state of repair of an engine can have significant effects on the performance of oxygen sensors. If there are no electrical issues in the heater control circuit of an oxygen sensor, there is little point in trying to diagnose oxygen sensor related issues if the engine is affected by excessive oil burning, poor combustion, vacuum leaks, exhaust leaks, or other issues that affect the overall performance of the engine and/or exhaust system.

Step 6

At this point, the repair should be complete, but to be sure, clear all codes and test drive the vehicle to see if the code returns. In the unlikely event that the code does return, there may be an intermittent fault present.

Finding and repairing an intermittent fault can be extremely challenging, and in some cases, the fault may have to be allowed to worsen before an accurate and definitive repair can be made.

Searches related to HO2S Heater Control Circuit High Bank 2 Sensor 3

• p0064 mercedes
• p0060 mercedes
• p0025 mercedes
• mercedes camshaft solenoid recall